In many fields [33,34]. A distinctive feature of TrkC Activator web polymers depending on N-vinylimidazole
In many fields [33,34]. A distinctive feature of polymers based on N-vinylimidazole (VI) is the presence of a pyridine nitrogen atom within the azole ring, which exhibits electron-donating properties. This presents wide possibilities for polymer modification. Such polymers proficiently sorb metal ions to afford the coordination complexes possessing catalytic activity [35,36]. By far the most critical feature of N-vinylimidazole polymers is solubility in water, on account of which they are extensively employed in medicine. They’ve higher physiological activity and are made use of as low molecular weight additives in medicines and as elements of drug Nav1.6 Inhibitor Compound carriers [37,38]. In this function, the synthesis and characterization of water-soluble polymer nanocomposites with distinct CuNP contents using non-toxic poly-N-vinylimidazole as an efficient stabilizer and ascorbic acid as an eco-friendly and organic reducing agent is reported. The interaction amongst polymeric modifiers along with the resultant CuNPs was also investigated. 2. Materials and Approaches two.1. Supplies The initial N-vinylimidazole (99 ), azobisisobutyronitrile (AIBN, 99 ), copper acetate monohydrate (Cu(CH3 COO)2 two O, 99.99 ), ascorbic acid (99.99 ) and deuterium oxide (D2 O) were purchased from Sigma-Aldrich (Munich, Germany) and made use of as received without having additional purification. Ethanol (95 , OJSC “Kemerovo Pharmaceutical Factory”, Kemerovo, Russia) was distilled and purified in accordance with the recognized procedures. H2 O was used as deionized. Argon (BKGroup, Moscow, Russia) having a purity of 99.999 was made use of inside the reaction. 2.2. Synthesis of Poly-N-vinylimidazole N-Vinylimidazole (1.5 g; 16.0 mmol), AIBN (0.018; 0.1 mmol), and ethanol (1.0 g) have been placed in an ampoule. The glass ampule was filled with argon and sealed. Then the mixture was stirred and kept inside a thermostat at 70 C for 30 h until the completion of polymerization. A light-yellow transparent block was formed. Then the reaction mixture PVI was purified by dialysis against water through a cellulose membrane (Cellu Sep H1, MFPI, Seguin, TX, USA) and freeze-dried to provide the polymer. PVI was obtained in 96 yield as a white powder. Additional, the obtained polymer was fractionated, plus the fraction with Mw 23541 Da was employed for the subsequent synthesis of the metal polymer nanocomposites. 2.three. Synthesis of Nanocomposites with Copper Nanoparticles The synthesis of copper-containing nanocomposites was carried out within a water bath under reflux. PVI (5.three mmol) and ascorbic acid (1.30.6 mmol) in deionized water had been stirred intensively and heated to 80 C. Argon was passed for 40 min. Then, in an argon flow, an aqueous remedy of copper acetate monohydrate (0.4.three mmol) was added dropwise for 3 min. The mixture was stirred intensively for another 2 h. The reaction mixture was purified by dialysis against water through a cellulose membrane and freezedried. Nanocomposites had been obtained as a maroon powder in 835 yield. The copper content material varied from 1.eight to 12.three wt .Polymers 2021, 13,three of2.four. Characterization Elemental analysis was carried out on a Thermo Scientific Flash 2000 CHNS analyzer (Thermo Fisher Scientific, Cambridge, UK). FTIR spectra were recorded on a Varian 3100 FTIR spectrometer (Palo Alto, CA, USA). 1 H and 13 C NMR spectra were recorded on a Bruker DPX-400 spectrometer (1 H, 400.13 MHz; 13 C, 100.62 MHz) at space temperature. The polymer concentrations have been ca. ten wt . Regular five mm glass NMR tubes were employed. A Shimadzu LC-20 Prominence technique (Shimadzu Corporat.